<noframes id="bxbhx"><form id="bxbhx"></form>
<address id="bxbhx"><listing id="bxbhx"><meter id="bxbhx"></meter></listing></address>
    <address id="bxbhx"><nobr id="bxbhx"><meter id="bxbhx"></meter></nobr></address>

    <noframes id="bxbhx"><form id="bxbhx"></form>
    <address id="bxbhx"><listing id="bxbhx"><meter id="bxbhx"></meter></listing></address>
      <address id="bxbhx"><nobr id="bxbhx"><meter id="bxbhx"></meter></nobr></address>

      <noframes id="bxbhx"><form id="bxbhx"></form>
      <address id="bxbhx"><listing id="bxbhx"><meter id="bxbhx"></meter></listing></address>
        <address id="bxbhx"><nobr id="bxbhx"><meter id="bxbhx"></meter></nobr></address>
        网站标志
        产品详情
         
        产品详情
        MTG内螺纹量仪

        Internal Gages

        INTERNAL GAGE FRAMES内螺纹量具本体

            The basic internal gage frames are available in two models. The G-600 with a capacity from .190 inches to 4.5 inches basic and the G-1200 with a capacity from 6 inches to 18 inches. The gage frames are extremely accurate, .000050 inch repeatability is guaranteed. The system was designed to take the abuse of shop use although it is precise enough for the requirements of the quality control or metrology laboratory. Two extension kits are available. The G-600X increases the capacity of the G-600 frame to 5.5 inches basic and the G-1200X increases the capacity of the G-1200 frame to 24 inches basic. The gaging pressure of both internal frames can be adjusted by the operator  thereby allowing very "thin wall" parts to be measured, minimizing destortion !
        Internal Gage FramesInternal Gage Frames

        INTERNAL GAGE FINGERS内螺纹量具测角

           MTG offers more sizes, types, and reaches of internal fingers than any other gage manufacturer. Fingers can be manufactured to measure most thread forms including Unified, Buttress, Acme, Stub Acme, Metric, Whitworth, Lowenherz, Ball, 40 Degree Worm, Aero, and Square. Additional geometries are available for bearing races, grooves, bores, tapered bores, gears, splines, and dovetails. Six different lengths are available.

         

                 FINGER PREFIX            OAL LENGTH OF FINGER                 MINIMUM / MAXIMUM DIAMETER 

        1.5U.................Basic Length 1.25 Inches..........Under 5/8 In. Diameter 
        1.5.................Basic Length 1.5 lnches..........5/8 In. Diameter & Over 
        2.25.................Basic Length 2.25 Inches ..........3/4 In. Diameter & Over
        3.0.................Basic Length 3.25 Inches..........1.0 In. Diameter & Over
        4.0................. Basic Length 4.12 Inches..........1.0 In. Diameter & Over
        5.0................. Basic Length 5.0 Inches..........l.5 In. Diameter & Over
        Internal Gage Fingers1Internal Gage Fingers2Internal Gage Fingers3

        INTERNAL GAGE STANDS

            MTG offers simplicity in measurement. Many times it is necessary for the user to measure more than one element of a thread. Shown below (pictured in red) is an Internal System for thread measurement. The first gage is set up to measure the pitch diameter, the second gage measures the diametrical equivalent of the form (single thread), and the third measures functional diameter. The gage stand shown (three risers) is a GS-3. Two risers is a GS-2. One riser is a GS-1. The GS-1 is expandable to either a GS-2 or GS-3 simply by purchasing additional risers because all three risers share a common base. A round base (GS-O) stand is used to hold the gage frame when measuring grooves and bores of a light weight part with a squaring plate installed.   (SEE INTERNAL BORES AND GROOVES BELOW) 

         


        Internal Gage Stand1Internal Gage Stand2Internal Gage Stand3
        GS-0GS-3 GS-3 

        Back to Top

        DEEP HOLE DIAMETERS 深内孔直径量仪

        Deep Hole Diameters
            The MTG Telescoping Tube System (TST) is far more accurate than its competitors who use long segments that bend and deflect. The system can be used on either the G-600 or G-1200 internal gage frames. The reason for its accuracy is the fact that it creates a"Linear" measurement. The TST System uses TST inserts which are available in all the geometries listed for the internal fingers. Diameters as large as 36 inches or more may be measured. There are three standard lengths available, 5 inch reach, 8 inch reach, and 10 inch reach. 

        INTERNAL BORES AND GROOVES深内沟槽量具

        Internal Bores and Grooves
            Only with the MTG System can a bore diameter, internal groove diameter, and their concentricity to each other be measured with a single gage.   This capability is due to the "MTG SQUARING PLATE" accessory. Four different squaring plates are available. All plates are slotted through their centers permitting the use of all our internal fingers.
           Squaring plate arms are adjustable for length so the reach of the fingers into any bore can be set to the desired dimension.


        SAMPLE SQUARING PLATE GAGE FRAME ASSEMBLIES 

         

        BORE & GROOVE INSPECTION

             CHECKING THE BORE
             Banking the workpiece against the squaring plate keeps the workpiece straight, so it is necessary to rock it in only one plane to find the high point of the diameter. The squaring plate may be moved in or out to permit gaging at any depth.
        Bore & Groove Inspection

        CHECKING THE GROOVE
            After bores have been inspected for diameter, the gage is quickly reset to groove diameter and the squaring plate moved to a point that sets the fingers for groove location. Next, reset the indicator, then proceed with gaging.

        CHECKING CONCENTRICITY
           With the gage still set for groove diameter, rotate two eccentric pins mounted in the squaring plate. Slide the plate until the pins bear down against the bore, taking the stationary finger out of contact with the groove. Since the upper finger is now reading the groove while the eccentric pins are contacting the bore, rotation of the workpiece will cause the indicator to show any runout between the two diameters.

        Back to Top

        ANTI-DEFLECTION BRACES

            Anti-deflection braces are recommended when using .000050 graduation mechanical indicators, electronic heads or where an error might be suspected because of the awkwardness of accessibility involved when measuring the part. Anti-deflection braces are available in 5 different lengths for internal fingers only. They are not necessary when using the TST System.
        Anti Deflection BracesAnti Deflection Braces


        Tapered Internal 

Threads

        TAPERED INTERNAL THREADS

            MTG now enables the operator or quality control inspector to accurately measure internal tapered threads. No tapered set masters are required. Simple L1 location setting is designed into the system. The system can be hand-held or stand mounted. Fingers are available to measure pitch diameter, functional diameter, minor diameter, included angle, and full form (single thread) on 60 degree tapered threads.

        QQ客服
        点击这里给我发消息  
        兼职赚钱在家 173| 240| 709| 391| 355| 188| 824| 323| 243| 846| 988| 205| 723| 821| 465| 957| 11| 405| 530| 990| 668| 314| 459| 559| 1| 666| 168| 702| 113| 351| 977| 801| 922| 662| 257| 747|